Retro-Renault Archive Forum Index  
SEARCH THE ARCHIVE FORUMS  •  Log in
Hello, you are currently browsing to Retro-Renault Archive which is a copy of our old forum. You cannot post replies in this forum. Please click here to go to the active website. 
 NOISE FROM DRIVE BELT
Author Message
schakal
Spammer

Joined: 27 Jul 2004
Posts: 5717

Posted: Thu Nov 25, 2004 5:47 am

just noticed yesterday that there is a funny screeching noise coming from the car especially when trying to accelerate in any gear .pulled over and opened the bonnet ,it sounds like the drive belt .
what could be happening ,any suggestions ?
Chris H
Forum Moderator

Joined: 02 Mar 2004
Posts: 19978

Posted: Thu Nov 25, 2004 6:22 am

its slipping, which is unusual for a serpentine belt.

But it may be a knackered bearing in something. Water pump, alt, ps pump etc.

See how loose the belt is and if its not loose take the belt off and spin the alt, water pump, ps pump by hand, they should rotate silently and easily.
schakal
Spammer

Joined: 27 Jul 2004
Posts: 5717

Posted: Thu Nov 25, 2004 10:58 am

how do i take the belt off chris ?
Chris H
Forum Moderator

Joined: 02 Mar 2004
Posts: 19978

Posted: Thu Nov 25, 2004 11:05 am

by removing it.

the tensioners on the front of the alt on your car iirc.
schakal
Spammer

Joined: 27 Jul 2004
Posts: 5717

Posted: Thu Nov 25, 2004 11:45 am

there is a tensioner bold and a tensioner locknut
which one do i slacken ?
Chris H
Forum Moderator

Joined: 02 Mar 2004
Posts: 19978

Posted: Thu Nov 25, 2004 12:23 pm

both, you need to loosen the alt lock nuts then you can wind the tensione rin/out.
schakal
Spammer

Joined: 27 Jul 2004
Posts: 5717

Posted: Thu Nov 25, 2004 1:14 pm

will have to see them on the car tomorrow . sounds like an easy job
but i am sure i will bug you later with my weird questions
cheers
schakal
Spammer

Joined: 27 Jul 2004
Posts: 5717

Posted: Fri Nov 26, 2004 7:55 am

inspected the drive belt today the noise is still there .in haynes it says drive belts need adjusting after a while on these cars . even though the belt was looking tight ,i could easily tighten the tensioner bolt about 10 turns and still is willing to tighten more .
by the way i discovered the belt is going around/turning 4 different wheels ,alternator ,water pump,power steering pump and the crank bit that turns all the stuff if i am right???

still cant dare to get the belt out cause i am not sure how i will be able to fit the new one in as there doesnot seem to be a lot of working space there .does the car need lifting up ?? or is it a just stick the new belt in and tighten the nuts jobby????

after getting the belt out lets say i found the water pump is ferked or alternator or the steering pump . and i dont have a spare in the shed plus the knowledge to stick the spare one in .
my most important question is , how long can i drive this way without replacing anything ,would the belt snap or is it damaging anything else out there at the moment ?


Last edited by schakal on Tue Dec 14, 2004 7:58 am; edited 1 time in total
Chris H
Forum Moderator

Joined: 02 Mar 2004
Posts: 19978

Posted: Fri Nov 26, 2004 10:35 am

its easy and the necxt time you start it you could wreck the engine or it may be fine for a million miles. Its easy to swap as is the water pump etc.
schakal
Spammer

Joined: 27 Jul 2004
Posts: 5717

Posted: Sat Nov 27, 2004 2:18 am

i called gsf for a new drive belt today ,they dont have the listing for 8v 1.8 SPI ,they have the 16v and 1,7models belts listed they say . but the guy confirmed it is running the pas pump as well. so i need some confirmation here pls . is it the same belt been used for the renault 19 1.7 engine ?
Chris H
Forum Moderator

Joined: 02 Mar 2004
Posts: 19978

Posted: Sat Nov 27, 2004 2:38 am

yes its the same.
schakal
Spammer

Joined: 27 Jul 2004
Posts: 5717

Posted: Sat Nov 27, 2004 4:06 am

you are a starman chris,will get it sorted today ,8 quid inc vat not bad ehhh
schakal
Spammer

Joined: 27 Jul 2004
Posts: 5717

Posted: Wed Dec 01, 2004 9:50 am

the belt has arrived finally today ,got it from gsf and took the old one out fit the new one in .
very easy job it was,after taking the belt out i turned the pulleys by hand ,alternator is the smoothest ,but all the rest tuens with no problems no noise .
the new belt made the same sort of noise for a bit(not as much as the old one) ,but did not have the time to try it on the road yet .is it going to get used to its place and cut the noise .do i need to adjust the new belt after a while???


Last edited by schakal on Tue Dec 14, 2004 7:58 am; edited 1 time in total
Chris H
Forum Moderator

Joined: 02 Mar 2004
Posts: 19978

Posted: Wed Dec 01, 2004 10:11 am

yep adjust it in a wee while.

My belt looks similar but the orions has sections missing and needs done asap.
schakal
Spammer

Joined: 27 Jul 2004
Posts: 5717

Posted: Wed Dec 01, 2004 11:33 am

god i just noticed my hands are ugly .
many thanks chris
Display posts from previous:      


 Jump to:   




SPIDER ARCHIVE
Powered by phpBB © 2001, 2002 phpBB Group :: FI Theme :: All times are GMT - 7 Hours