Retro-Renault Archive Forum Index  
SEARCH THE ARCHIVE FORUMS  •  Log in
Hello, you are currently browsing to Retro-Renault Archive which is a copy of our old forum. You cannot post replies in this forum. Please click here to go to the active website. 
 combi boiler
Author Message
Chris H
Forum Moderator

Joined: 02 Mar 2004
Posts: 19978

Posted: Sun Dec 12, 2004 6:26 am

anyone ken the going rate for a 3.5BAR safety valve?

Had an ongoing problem since the boiler was first installed and as usual plumbers etc don't have a clue. Its about 6/7 years old.

Anyway, the pressure has never held in the boiler so you always have to top it up via the loop circuit.

Today the cry of water resonated throughout the house. So I finally decided to have a gander, chronic laziness is a condition not a voluntary exercise!

I found the union into the back of the saftey valve was loose and thus leaking. So I tightened it.

I then topped up the pressure and heard the valve was leaking internally. A shove on the red cap soon stopped the flow and silenced it. A new one is needed. So my theory is this valve has always been faulty. To open it you twist is counterclockwise 1/4 turn and it empties. Its 3.5 bar set so theres obviously a spring and ball bearing or somethign in there to prevent the flow.

heres some pics of said item.

Image

ariston eurocombi

Image

Image

so I need to get another valve and fit it.

All the plumbing shops are shut today so was just wondering if anyone knew the going rate for one.
mals
Self Proclaimed Comic Genius

Joined: 04 Jul 2004
Posts: 3482

Posted: Sun Dec 12, 2004 6:33 am

Have you tried http://www.wickes.co.uk dont know if there is a store near you, but they do plumbing bits
Chris H
Forum Moderator

Joined: 02 Mar 2004
Posts: 19978

Posted: Sun Dec 12, 2004 6:38 am

cheers, but it says this

This site is currently not transactional. This part of the site is still being developed.


Screwfix website http://www.screwfix.com doesn't do them either.

i can see me having to order it.
david3533
Site Subscriber

Joined: 02 Oct 2004
Posts: 1575

Posted: Sun Dec 12, 2004 6:41 am

try this one chris, don't know if they do what your after http://www.focusdiy.co.uk/
david3533
Site Subscriber

Joined: 02 Oct 2004
Posts: 1575

Posted: Sun Dec 12, 2004 6:43 am

b&q on www.diy.com
Chris H
Forum Moderator

Joined: 02 Mar 2004
Posts: 19978

Posted: Sun Dec 12, 2004 6:45 am

cheers but it appears this is not meant to be a diy effort. So the plumb centre it may have to be.
Chris H
Forum Moderator

Joined: 02 Mar 2004
Posts: 19978

Posted: Sun Dec 12, 2004 6:50 am

http://www.plumbcenter.co.uk/plumb/default.html

they have one. £5.39, need to wait till tomoz to get.
srr
Level 8 User

Joined: 02 Dec 2004
Posts: 263

Posted: Sun Dec 12, 2004 4:33 pm

Hmmm, u dont have hot water into the house???
Chris H
Forum Moderator

Joined: 02 Mar 2004
Posts: 19978

Posted: Mon Dec 13, 2004 2:08 am

yes but it leaks away out of the boiler due to the dodgy valve.

need to go and get a new valve later on.
Chris H
Forum Moderator

Joined: 02 Mar 2004
Posts: 19978

Posted: Mon Dec 13, 2004 11:24 am

well managed to get one that was useless.

Anyway had to go to 3 places to eventually get one.

Whilst we were at the 2nd establishment (plumb centre) I spotted a performance car place beside it

Image

look at that, yes a 190 merc cossie, had the big spoiler and everything, rare beast.

Anyway back home and the new and old valves

Image

were it goes

Image

Basically the new valve didn't go. It was to long and it turned through 90 more degrees to seal, theres no provision for me to fit a washer so I stripped the old valve and cleaned otu the crap and then stuck it back in. Seemed to have worked.

Strippign it and cleanign it is what I should have done in the 1st place.

Anyway took the combustion chamber cover off etc to hoover it out

Image

the roof of the chamber is th eheat exhanger, just like a heat matrix.
Display posts from previous:      


 Jump to:   




SPIDER ARCHIVE
Powered by phpBB © 2001, 2002 phpBB Group :: FI Theme :: All times are GMT - 7 Hours