Retro-Renault Archive Forum Index  
SEARCH THE ARCHIVE FORUMS  •  Log in
Hello, you are currently browsing to Retro-Renault Archive which is a copy of our old forum. You cannot post replies in this forum. Please click here to go to the active website. 
 clio suspension swap
Author Message
Rich1
Level 7 User

Joined: 21 Feb 2005
Posts: 224

Posted: Mon Mar 14, 2005 4:08 pm

i have just got myself some valver suspension sorted consisting of dampers, springs, ARB, struts and driveshafts, i'm wondering if i can put them on without the shafts, struts and ARB before changing the engine over or do i need to put the arb or struts on? basically to keep the amount if bits i have lying around to a minimum! mine is a 1.2 rl versailles atm so any info would be great.
If it makes a difference i'm putting the 16valve brake set up on too consisting of pads calipers and carriers
Chris H
Forum Moderator

Joined: 02 Mar 2004
Posts: 19978

Posted: Tue Mar 15, 2005 1:03 am

Does the 1.2 have a standard ARB? If ity does then its prob the same as the 16V, the 19's all use the same one.

But yes you can just stick ont he 16V suspension and leave the rest till later.

The hubs may be the different bolt spacing though (52mm vs 54mm), so you had better check that 1st.
Rich1
Level 7 User

Joined: 21 Feb 2005
Posts: 224

Posted: Tue Mar 15, 2005 3:21 am

i am unsure on both of those potential problems so i'll have to do some more research, if the hubs are different any ideas how much they are and where i can pick them up from?
Chris H
Forum Moderator

Joined: 02 Mar 2004
Posts: 19978

Posted: Tue Mar 15, 2005 3:30 am

tenner at a scrappy...
Bridges
Level 3 User

Joined: 13 May 2004
Posts: 79

Posted: Tue Mar 15, 2005 5:27 am

Silly question.... Long term with larger 15 or 16 inch wheels would these fit the 1.2 clio's front and rear arches along with the 16v suspension? Are the wider panels on the 1.8 16v for show?
Chris H
Forum Moderator

Joined: 02 Mar 2004
Posts: 19978

Posted: Tue Mar 15, 2005 5:45 am

if you use the 16V rear axle and full front susnsion incl wishbones etc then yes you really need the flared arches to ensure theres no scrubbing.
Rich1
Level 7 User

Joined: 21 Feb 2005
Posts: 224

Posted: Tue Mar 15, 2005 1:22 pm

i have 16valver front arches fitted so it's not a problem and i'm on the look out for an RSI rear beam for the disc conversion so it doesn't matter
david3533
Site Subscriber

Joined: 02 Oct 2004
Posts: 1575

Posted: Wed Mar 16, 2005 12:45 am

hope it comes with top mounts mate other wise you'll have too much camber so get the 16v top mounts
Rich1
Level 7 User

Joined: 21 Feb 2005
Posts: 224

Posted: Wed Mar 16, 2005 5:09 am

good lad i forgot about those Embarassed is one of these at the link below for lowered and non nlowered at all? i'm unsure which i need
http://www.eurocarparts.com/ecommerce/Search_Results.asp
JB
Mr Quoter-vator

Joined: 16 Feb 2004
Posts: 7405

Posted: Wed Mar 16, 2005 6:25 am

that link wont work.

get to the pade again and copy and paste the text in here.
Rich1
Level 7 User

Joined: 21 Feb 2005
Posts: 224

Posted: Wed Mar 16, 2005 7:11 am

FEBI n/a 609745000 STRUT BEARING FRONT CLIO/TWINGO .
TOP BEARING £6.50
SASIC n/a 609745040 SHOCK TOP MOUNT CLIO HEIGHT 35MM SHOCK TOP MOUNT CLIO HEIGHT 35MM
HEIGHT 35MM - Sell in pairs £9.50
SASIC n/a 625745300 SHOCK TOP MOUNT CLIO HEIGHT 41MM LIP ON BOTTOM
HEIGHT 41MM - Sell in pairs £8.95
Chris H
Forum Moderator

Joined: 02 Mar 2004
Posts: 19978

Posted: Wed Mar 16, 2005 7:34 am

you need to measure the top mounts you have and get the right sized replacements.
Rich1
Level 7 User

Joined: 21 Feb 2005
Posts: 224

Posted: Wed Mar 16, 2005 7:50 am

the ones i have on the 1.2 at the moment i presume?
Chris H
Forum Moderator

Joined: 02 Mar 2004
Posts: 19978

Posted: Wed Mar 16, 2005 7:57 am

well if your going to fit 16V gear and you want new top mount for the 16V stuff then you need to measure the 16V bits.
Rich1
Level 7 User

Joined: 21 Feb 2005
Posts: 224

Posted: Wed Mar 16, 2005 8:01 am

fair enough but i don't currently have 16 top mounts do i! so in other words i need to get them measured off the car they are coming off?
Chris H
Forum Moderator

Joined: 02 Mar 2004
Posts: 19978

Posted: Wed Mar 16, 2005 8:04 am

top mounts are fitted to the struts so wait until you get them
Rich1
Level 7 User

Joined: 21 Feb 2005
Posts: 224

Posted: Wed Mar 16, 2005 8:06 am

ok cool thanks (yes i am currently a bit of a dumbass with this stuff but only young and learning) ah well i'll try not to ask the same questions twice at least
Rich1
Level 7 User

Joined: 21 Feb 2005
Posts: 224

Posted: Wed Mar 16, 2005 2:16 pm

just found out they are already on the struts so no need to buy them Cool
Bridges
Level 3 User

Joined: 13 May 2004
Posts: 79

Posted: Wed Mar 16, 2005 4:11 pm

Another stupid question...

If you fit front clio 16v front suspension, increasing the track which is cool as Rich says he has the plastic front 16v wings. Would this not mean you should change to the 16v torsion bar which is uprated and with hubs all in all that are wider to keep suspension set up similar? Or will this not make too much difference. Confused
Rich1
Level 7 User

Joined: 21 Feb 2005
Posts: 224

Posted: Wed Mar 16, 2005 7:07 pm

if i had about £300 just to fit the rear arches i would but it aint gonna make a ridicoulos amount of difference! the rear discs are really just for show tbh they aint tht much better than drums inho
Chris H
Forum Moderator

Joined: 02 Mar 2004
Posts: 19978

Posted: Thu Mar 17, 2005 1:35 am

wider rear track does help the handling but its not to much of an issue really.
Display posts from previous:      


 Jump to:   




SPIDER ARCHIVE
Powered by phpBB © 2001, 2002 phpBB Group :: FI Theme :: All times are GMT - 7 Hours