Retro-Renault Archive Forum Index  
SEARCH THE ARCHIVE FORUMS  •  Log in
Hello, you are currently browsing to Retro-Renault Archive which is a copy of our old forum. You cannot post replies in this forum. Please click here to go to the active website. 
 Leccy Window Regulator
Author Message
Sic Puppy
Site Subscriber

Joined: 01 Feb 2005
Posts: 728

Posted: Tue May 03, 2005 3:17 pm

Windows packed up again (fully down of course Mad ). I've taken the door to bits and checked the wire and all that. I took the plug off the regulator behind that foam on the top left of the door and checked it with a multimeter. 12v's it read. So is there anything else I should try tomorrow before going down the scrappys for a replacement? I've had to wrap the window up in a bin bag to keep the rain (typical) out tonight Very Happy

Cheers Guys
Iain
Smirn
Level 1 User

Joined: 03 May 2005
Posts: 26

Posted: Tue May 03, 2005 3:28 pm

Is the motor sounding like it is labouring or clicking? Or not working at all?
Sic Puppy
Site Subscriber

Joined: 01 Feb 2005
Posts: 728

Posted: Tue May 03, 2005 3:48 pm

It's a clicking like when the window is fully up and up click the window to go up again. ie it clicks off.
Smirn
Level 1 User

Joined: 03 May 2005
Posts: 26

Posted: Tue May 03, 2005 3:56 pm

Have you tried lubricating the runners? From my experience a window will not work if it is clogged up with sh1t, the motor labours and the regulator stops the power. Windows never get serviced but they do need it. A spray of WD40 might smear the windows a little on the edges but it saves problems later on in life.
Sic Puppy
Site Subscriber

Joined: 01 Feb 2005
Posts: 728

Posted: Tue May 03, 2005 3:59 pm

I'll give it a go. However this has happened before. I have left it overnight and then magically in the morning it will work again. Cheers for the advice buddy. Hope it solves it. The glass holder looks like a right bugger to get off!
Smirn
Level 1 User

Joined: 03 May 2005
Posts: 26

Posted: Tue May 03, 2005 4:01 pm

Probably because the rain lubricated it a bit. Hope you find the cure, no problem on the advice. Hard to diagnose sat here. Good luck
Sic Puppy
Site Subscriber

Joined: 01 Feb 2005
Posts: 728

Posted: Tue May 03, 2005 11:35 pm

Well lubed it with a cand of WD40 at about 2am last night before I went to bed. Tried it this morning and......No Change Sad . So looks like it's a hunt for a new/2nd hand regulator. Just hope I can find one Confused

Cheers for all the help guys. Appriciate it as always Smile
Iain
Smirn
Level 1 User

Joined: 03 May 2005
Posts: 26

Posted: Wed May 04, 2005 12:35 am

At least it will stop the replacement becoming U/S. Smile
Sic Puppy
Site Subscriber

Joined: 01 Feb 2005
Posts: 728

Posted: Wed May 04, 2005 5:02 am

Well...I managed to get the regulator out (taking the glass out first helps a lot!).

Can't see much wrong with it. It started working again out of the door but froze again halfway up. Think there must be something sticking inside the motor.

Here's some Pics anyway just for the hell of it Very Happy

Image
Link http://img214.echo.cx/img214/5931/dscf00039rq.jpg

Image
Link http://img214.echo.cx/img214/3530/dscf00045ww.jpg

Image
Link http://img214.echo.cx/img214/7726/dscf00075ny.jpg
Smirn
Level 1 User

Joined: 03 May 2005
Posts: 26

Posted: Wed May 04, 2005 5:18 am

Still think it was what I said orginally. I looked on the Renault TIS too (found nothing). It is just resistance going up and down. If the resistance is too much this is what will happen. Hence why it works when not fitted.

Does the glass move in the runners smoothly when pushed up and down by hand? If not spray down the window runners until it does

Does the motor run all the way out of the car? If it does there is not a lot wrong with it, refer to above. If not it is a scrap yard run you need.
schakal
Spammer

Joined: 27 Jul 2004
Posts: 5717

Posted: Sat May 07, 2005 9:43 am

give direct 12v to the electrodes and see if its working


if not ,the motor is buggered unless the electrodes are not ferked

the motor itself is a sealed mechanism by the way ,its quite hard to put it back once you open the whole thing
Sic Puppy
Site Subscriber

Joined: 01 Feb 2005
Posts: 728

Posted: Sat May 07, 2005 5:24 pm

Problm in the end was a loose connection on the connecter plug to the motor. When it was connected properly it shorted out. When the plug was pulled out 1-2mm it worked! LOL!! Swapped for the scrappy one any way and put a rubber seal in the motor end to keep the plug 2mm from sitting flush.

Was driving around with the regulator in the back seat for two days with an empty fag paket keeping the window from falling LOL!! Felt a bit thick when I found out the problem. But at least that solved the "it sometimes works" problem!
bison
Level 1 User

Joined: 20 Sep 2005
Posts: 27

Posted: Fri May 05, 2006 11:41 am

same problem on my 19,they packed in drivers side for good today,it used to be every now and then,tried everything even wired up a spare motor,turned out to be the same as this thread,nice one!!!!!!!!!!!!!!!!!!
Display posts from previous:      


 Jump to:   




SPIDER ARCHIVE
Powered by phpBB © 2001, 2002 phpBB Group :: FI Theme :: All times are GMT - 7 Hours