Retro-Renault Archive Forum Index  
SEARCH THE ARCHIVE FORUMS  •  Log in
Hello, you are currently browsing to Retro-Renault Archive which is a copy of our old forum. You cannot post replies in this forum. Please click here to go to the active website. 
 R19 OIL PRESSURE
Author Message
JIMGR
Newbie

Joined: 30 Sep 2005
Posts: 6

Posted: Fri Sep 30, 2005 10:57 am

My R19 1.4(EJ6 engine) has an oil pressure warning light switch.Is it an oil pressure sensor too?The needle only rises when you turn the key before the starting.When the engine is running the the needle is not working?Is that normal?
Roger Red Hat
Site Subscriber

Joined: 13 Oct 2004
Posts: 4722

Posted: Fri Sep 30, 2005 10:59 am

yes thats fine, its an oil level gauge.

turns off once engine is started.
JIMGR
Newbie

Joined: 30 Sep 2005
Posts: 6

Posted: Fri Sep 30, 2005 12:37 pm

Τhank you my friend.I have another question.Many times the needle does not rise at all before starting.What is malfunctioning?The sensor or the instrument in the panel?In this case when i move the key anticlockwise to pull out the key the needle tries to move but it doesn`t rise.
schakal
Spammer

Joined: 27 Jul 2004
Posts: 5717

Posted: Fri Sep 30, 2005 12:54 pm

the oil pressure sensor gets clogged sometimes
no big deal though mate ,as long as you check your oil level regularly and have not got major leaks ,you are fine
JIMGR
Newbie

Joined: 30 Sep 2005
Posts: 6

Posted: Fri Sep 30, 2005 1:02 pm

Τhanks.Do you think that a sensor change would solve the problem?What
is the most suitable type of oil for this engine?May it gets clogged from the oil i use (ELF 20W50)
schakal
Spammer

Joined: 27 Jul 2004
Posts: 5717

Posted: Fri Sep 30, 2005 1:09 pm

it might be the oil you use or something else in the oil ways ,the sensor does the reading through a little hole so if something is gone in there you might have problems with the reading .

but as i said earlier ,this is nothing to be bothered with ,dont make a fuss about it
but if you are so fussy beyond help ,get the sensor out when you change your oil next time and use a engine oil flush agent to clear most of the crap in the engine . clean the sensor and put it back in
JIMGR
Newbie

Joined: 30 Sep 2005
Posts: 6

Posted: Fri Sep 30, 2005 1:14 pm

ΟΚ.Τhanks
Chris H
Forum Moderator

Joined: 02 Mar 2004
Posts: 19978

Posted: Sat Oct 01, 2005 10:21 am

use 10W40
JIMGR
Newbie

Joined: 30 Sep 2005
Posts: 6

Posted: Sat Oct 01, 2005 11:00 am

Τhanks for your help.I don`t know if it is important but i`ve forgotten to say that the engine is hot almost always when the needle does not rise.On the contrary when the engine is cold the needle rises always.
schakal
Spammer

Joined: 27 Jul 2004
Posts: 5717

Posted: Sat Oct 01, 2005 11:29 am

use an oil cooler in that case Laughing
Chris H
Forum Moderator

Joined: 02 Mar 2004
Posts: 19978

Posted: Sat Oct 01, 2005 12:05 pm

schakal what are you talking about? Apart from a load of crap.

Its probably not working when hot as its a fine wire thats used for the oil level so when hot it goes open circuit.
JB
Mr Quoter-vator

Joined: 16 Feb 2004
Posts: 7405

Posted: Mon Oct 03, 2005 6:19 am

or perhaps if you mean hot as you just been switched off, you are not giving the oil a chance to settlle in the sump to give maximum reading??
JIMGR
Newbie

Joined: 30 Sep 2005
Posts: 6

Posted: Mon Oct 03, 2005 1:18 pm

No the needle does not rise at all even you have switched off the engine 30 minutes before.The engine must be completelely cold so the needle rises.
JB
Mr Quoter-vator

Joined: 16 Feb 2004
Posts: 7405

Posted: Mon Oct 03, 2005 1:34 pm

ok, well either way, forget it. its not exactly majorly important.
Display posts from previous:      


 Jump to:   




SPIDER ARCHIVE
Powered by phpBB © 2001, 2002 phpBB Group :: FI Theme :: All times are GMT - 7 Hours