Retro-Renault Archive Forum Index  
SEARCH THE ARCHIVE FORUMS  •  Log in
Hello, you are currently browsing to Retro-Renault Archive which is a copy of our old forum. You cannot post replies in this forum. Please click here to go to the active website. 
 possible driveshaft
Author Message
touring_19_16v
Level 10 User

Joined: 27 Apr 2005
Posts: 620

Posted: Fri Nov 04, 2005 4:19 pm

hey guys well anuther problem ere

right left the girlfriends house and turned left out her road and went to turn right at the junction, car moved then sumthing started grinding and there was no drive just grinding noises wen you let the clutch off, however if you turn the steering full lock right and slowly let the clutch off the car would move, if the steering was straight or full lock left no drive and grinding noises, RAC towed me home and suggested the driveshaft join. for some weeks now evrytime i turned right you would get a knocking sound frm the nsf and when you turn left i.e at a roundabout you get sqeeking noises like your braking, after metioning this to the RAC guy he was 95% sure it was the driveshaft join

what you guys reckon???
touring_19_16v
Level 10 User

Joined: 27 Apr 2005
Posts: 620

Posted: Fri Nov 04, 2005 4:38 pm

sorry guys 1 more thing i also noticed over the past two weeks the steering wheel sits left a fair bit when driving straight dunno if that would help aswell


cheers jay
huwwatkins
Site Subscriber

Joined: 10 Jun 2004
Posts: 2317

Posted: Fri Nov 04, 2005 5:07 pm

Go with that the RAC guy said, he's probably right.
touring_19_16v
Level 10 User

Joined: 27 Apr 2005
Posts: 620

Posted: Fri Nov 04, 2005 5:20 pm

ive just tried to move it, stuck it in reverse turned right and it did move back up the hill a bit but then slipeed and started grinding again feels like the force when it slips is coming frm the left had side when it slips would i need to change the whole shaft or can i change it frm the split pin if the outer CV join is the prob and not the spider inside the g/box
huwwatkins
Site Subscriber

Joined: 10 Jun 2004
Posts: 2317

Posted: Fri Nov 04, 2005 5:41 pm

If its the passenger side then you have remove the 3 inner bolts that attach the shaft/gater to the box and remove the whole lot. Changing the box oil while your at it might not be a bad idea, unless its been done recently. IF its the driver's side then just hammer out the roll pin and it pulls off .
touring_19_16v
Level 10 User

Joined: 27 Apr 2005
Posts: 620

Posted: Sat Nov 05, 2005 3:15 am

cool thnx huw?? how can you tell which side has gone???
touring_19_16v
Level 10 User

Joined: 27 Apr 2005
Posts: 620

Posted: Sat Nov 05, 2005 4:50 am

hey guys well now tht i got some light i went to have a look at our little problem, wen you turn the wheel i doesnt turn the driveshaft, so i looked underneath to find a split and gone CV gaiter so the problem is now tht i will definately need a ns driveshaft and quick has any1 got 1 near to me????????
Chris H
Forum Moderator

Joined: 02 Mar 2004
Posts: 19978

Posted: Sat Nov 05, 2005 8:23 am

if the engine jumps like a bastard when it happens then the drivers side has probably popped, the grease etc everywhere will give the game away.
touring_19_16v
Level 10 User

Joined: 27 Apr 2005
Posts: 620

Posted: Sat Nov 05, 2005 8:31 am

to tell you the truth chris my old m8 all the grese is all over the inside of the pax wheel over the strut and so on the drivers side is as clean as whistle no grease oil rust nuthing all has happend on the pax side
Display posts from previous:      


 Jump to:   




SPIDER ARCHIVE
Powered by phpBB © 2001, 2002 phpBB Group :: FI Theme :: All times are GMT - 7 Hours