Retro-Renault Archive Forum Index  
SEARCH THE ARCHIVE FORUMS  •  Log in
Hello, you are currently browsing to Retro-Renault Archive which is a copy of our old forum. You cannot post replies in this forum. Please click here to go to the active website. 
 Bonnet release cable
Author Message
Chet T16
Retroholic

Joined: 12 Feb 2004
Posts: 5685

Posted: Wed Nov 30, 2005 9:30 am

Its stretched on HMS Girlfriends car and now needs to people to open it

Can it be adjusted or is it new cable time?
Chris H
Forum Moderator

Joined: 02 Mar 2004
Posts: 19978

Posted: Wed Nov 30, 2005 9:44 am

new cable.

ph2 cables seem to snap a lot I have found.

You can extend it as there shoudl be 2 holes on the bit at the catch, use the other hole. Not all cables have that though.

best to replace it.

I need to do project Y's. Dash off job to do it properly btw.

Or use the lhd set up which is a much shorter cable and won;t need the dash ripped off I would imagine.
Chet T16
Retroholic

Joined: 12 Feb 2004
Posts: 5685

Posted: Wed Nov 30, 2005 9:45 am

Ooh that sounds like fun!

The general might donate its bonnet pins lol
Chris H
Forum Moderator

Joined: 02 Mar 2004
Posts: 19978

Posted: Wed Nov 30, 2005 9:46 am

I'm sure she'll be impressed with that!
Chris H
Forum Moderator

Joined: 02 Mar 2004
Posts: 19978

Posted: Wed Nov 30, 2005 9:49 am

lhd cable

77 00 821 013 CABLE BONNET LHD 14.96 ---3 x 1

rhd cable

77 00 821 014 CABLE BONNET 15.63 ---3 x 1

lhd is about half the length as well.
Chet T16
Retroholic

Joined: 12 Feb 2004
Posts: 5685

Posted: Wed Nov 30, 2005 10:32 am

This would mean switching the handle to the other side i assume?
Chris H
Forum Moderator

Joined: 02 Mar 2004
Posts: 19978

Posted: Wed Nov 30, 2005 10:34 am

obviously Rolling Eyes

but you don't need to remove the dash.
Chet T16
Retroholic

Joined: 12 Feb 2004
Posts: 5685

Posted: Wed Nov 30, 2005 10:38 am

lol yeah that was a stupid question

So i'll need a new handle?
Chris H
Forum Moderator

Joined: 02 Mar 2004
Posts: 19978

Posted: Wed Nov 30, 2005 10:42 am

handle is part of the cable mofo.

Unscrew the old one (t30 long mofo screw) then pull the cable through, it runs behidn the heater box etc.

push new cable through in passenger footwell, then clear the way a bit, helps if you undo the 13mm nuts under the speaker grille on the dashtop and under the cove ront he bottom of the dash to get more room.

You will see the screw hole, thats where it mounts, 1 screw and the back edge or front from the drivers point is held by a lug on the handle.
Chet T16
Retroholic

Joined: 12 Feb 2004
Posts: 5685

Posted: Wed Nov 30, 2005 1:12 pm

Thats what i'll do so Very Happy
Display posts from previous:      


 Jump to:   




SPIDER ARCHIVE
Powered by phpBB © 2001, 2002 phpBB Group :: FI Theme :: All times are GMT - 7 Hours