Retro-Renault Archive Forum Index  
SEARCH THE ARCHIVE FORUMS  •  Log in
Hello, you are currently browsing to Retro-Renault Archive which is a copy of our old forum. You cannot post replies in this forum. Please click here to go to the active website. 
 Manual Rack Conversion
Author Message
mixpioneer
Site Subscriber

Joined: 29 Dec 2004
Posts: 395

Posted: Sun Dec 04, 2005 2:18 pm

Has anyone got any good info on doing a manual rack conversion on a clio.

I pressume that you can fit the manual rack and column straight on. Its just the aux belt issues when you remove the ps pump.

Anyone seen how this has been done before?

Ta!
david3533
Site Subscriber

Joined: 02 Oct 2004
Posts: 1575

Posted: Mon Dec 05, 2005 1:13 am

on a 16v you need a 110mm long aux belt you will also need to modify the timing belt cover as the slots the belt goes through will not postioned correctly when you take the ps pump off.
Chris H
Forum Moderator

Joined: 02 Mar 2004
Posts: 19978

Posted: Mon Dec 05, 2005 1:35 am

clio is different David.

You need the rack and the column.
u33db
Affiliate

Joined: 13 Jan 2005
Posts: 219

Posted: Thu Dec 08, 2005 6:56 am

Yep, I had this done on my old 16v.

You need a manual steering rack and a manual steering column as the PAS one will be too short. You also need a shorter replacement belt and two brackets to hold the alternator on...i was looking at these parts in dialogies last week and you i'm 95% sure you can get them off a manual steering equipped 1.8 8v F-series engine. I can try and get the car code if need be but its about 50quid for the brackets and another couple of quid for the belt unless you can find them in a scrappy.
u33db
Affiliate

Joined: 13 Jan 2005
Posts: 219

Posted: Thu Dec 08, 2005 6:58 am

Theres also a pic of it in the clio haynes manual...i'll get you the page number later.
mixpioneer
Site Subscriber

Joined: 29 Dec 2004
Posts: 395

Posted: Thu Dec 08, 2005 8:09 am

Cheers for the info.

Is there any difference between the manual clio racks?

I got a 1.2 and a 1.4, the 1.2 is already being butchered so i'd preferably use the one off there??
mixpioneer
Site Subscriber

Joined: 29 Dec 2004
Posts: 395

Posted: Thu Dec 08, 2005 8:12 am

Oh yeah . . . is David right with the required belt length??
Chris H
Forum Moderator

Joined: 02 Mar 2004
Posts: 19978

Posted: Thu Dec 08, 2005 8:19 am

those racks are fine, davids belt length should be ok
u33db
Affiliate

Joined: 13 Jan 2005
Posts: 219

Posted: Thu Dec 08, 2005 9:09 am

mixpioneer wrote:
Cheers for the info.

Is there any difference between the manual clio racks?

I got a 1.2 and a 1.4, the 1.2 is already being butchered so i'd preferably use the one off there??


Not that i know of but i could be wrong.

The one i got from the scrappy for my old 16v was actually from a 1.2 and it was fine...all i had to do was buy new trackrod ends as it was using a different type.
u33db
Affiliate

Joined: 13 Jan 2005
Posts: 219

Posted: Thu Dec 08, 2005 11:57 am

Haynes page 2D.17, figs 5.13 and 5.17.

I think the vehicle code for dialogies etc is 357A if your buying new...the brackets and belt add up to about 50/60quid.

Smile
mixpioneer
Site Subscriber

Joined: 29 Dec 2004
Posts: 395

Posted: Fri Dec 09, 2005 8:42 am

Your a legend mate.

Cheers for all the help all.

I'll be sure to write a progress report (plenty of pics) when i get round to doing it.
Won't be til weather starts to warm up though.
Display posts from previous:      


 Jump to:   




SPIDER ARCHIVE
Powered by phpBB © 2001, 2002 phpBB Group :: FI Theme :: All times are GMT - 7 Hours