Retro-Renault Archive Forum Index  
SEARCH THE ARCHIVE FORUMS  •  Log in
Hello, you are currently browsing to Retro-Renault Archive which is a copy of our old forum. You cannot post replies in this forum. Please click here to go to the active website. 
 uh oh!
Author Message
mixpioneer
Site Subscriber

Joined: 29 Dec 2004
Posts: 395

Posted: Mon Dec 12, 2005 9:16 am

Car has been making a bit of a clunking sound in between braking and accelerating. Car is fine at higher speed but it's just when starting and stopping in traffic.
Thought it could be CV joints, lower ball joints, wishbone bushes.

But, after inspection today it's coming from the diff housing, and i have noticed i can pull the offside driveshaft in and out of the housing a good 4mm.
With both wheels off the ground and the car in first gear, i can rock the wheels back and forth quite a bit and it makes quite a nasty crunch/clunk noise.

Is this new box time or does it sound like a replaceable part has failed?
Dan
Site Subscriber

Joined: 28 Jan 2005
Posts: 3547

Posted: Mon Dec 12, 2005 9:23 am

box time
mixpioneer
Site Subscriber

Joined: 29 Dec 2004
Posts: 395

Posted: Mon Dec 12, 2005 9:30 am

Can't the diff be replaced on it's own?
Chris H
Forum Moderator

Joined: 02 Mar 2004
Posts: 19978

Posted: Mon Dec 12, 2005 9:51 am

yes but its a bastard and the box is now more than likely damaged.

before we say anythign else is the o/s shaft got the roll pin in?
mixpioneer
Site Subscriber

Joined: 29 Dec 2004
Posts: 395

Posted: Mon Dec 12, 2005 9:59 am

errrr, just had a look, it's got some of it in, looks like its had the end's drilled off to get the shaft off.

I tried to see if the end of the shaft is sliding about but it seems quite secure.

Could this be the cause of the problem?
Chris H
Forum Moderator

Joined: 02 Mar 2004
Posts: 19978

Posted: Mon Dec 12, 2005 10:03 am

if the shafts slidign about ont eh spindle then yes it can make noises.
mixpioneer
Site Subscriber

Joined: 29 Dec 2004
Posts: 395

Posted: Mon Dec 12, 2005 10:10 am

Yea, i did check that and the shaft is seems to be stuck fast.

All the play is where the spindle enters the diff housing, and when you rotate the wheel with it in gear there seems to be far too much play and noise coming from the diff.
Chris H
Forum Moderator

Joined: 02 Mar 2004
Posts: 19978

Posted: Mon Dec 12, 2005 10:40 am

knackered then
donsrno1
Level 10 User

Joined: 04 Nov 2005
Posts: 575

Posted: Mon Dec 12, 2005 3:09 pm

Should the nearside driveshaft have any sort of movement to and from the box in it? Just wondering because I think mine could be moved a bit when I was replacing the hub on my car.
Dan
Site Subscriber

Joined: 28 Jan 2005
Posts: 3547

Posted: Mon Dec 12, 2005 3:27 pm

yep, thats fine.
mixpioneer
Site Subscriber

Joined: 29 Dec 2004
Posts: 395

Posted: Sun Dec 18, 2005 6:33 am

I have been told that the problem with my diff could be the bearings, which can be replced in the car.

Is this likely, or should i just go with the new box thing.

If i do go for a new box, does it matter which one it is, or will all JB3 boxes fit.
Mine has an ally sump, will a tin sump box fit?

Gonna need some help with this one.
It's now making a nice rattling noise, and clunking worse than ever Confused

This is all too bad timing
Chris H
Forum Moderator

Joined: 02 Mar 2004
Posts: 19978

Posted: Sun Dec 18, 2005 6:38 am

how can it be done in the car?

Can they teleport the diff out put the bearings in then teleport it back in?

if so can I have their number please.

any J series box will fit.
Dan
Site Subscriber

Joined: 28 Jan 2005
Posts: 3547

Posted: Sun Dec 18, 2005 6:51 am

Chris H wrote:
Can they teleport the diff out put the bearings in then teleport it back in?

if so can I have their number please.


Well i be buggered! thats what i thought!
mixpioneer
Site Subscriber

Joined: 29 Dec 2004
Posts: 395

Posted: Sun Dec 18, 2005 6:57 am

Fair enough, didn't think the repairing was a feasible option, sounded all a bit too simple.

Anyway, back to the box fitting.
Don't i remember reading a post on here where someones gearbox didn't fit properly and there was a big gap at the bottom?

Think it was down to the ally / tin sump issue.

Did it turn out it was ok like that?
Chris H
Forum Moderator

Joined: 02 Mar 2004
Posts: 19978

Posted: Sun Dec 18, 2005 7:06 am

its fine.

my white chammy is like that.

Jimbo said hios worked loose but I have never see tnat happen.
mixpioneer
Site Subscriber

Joined: 29 Dec 2004
Posts: 395

Posted: Mon Dec 19, 2005 2:47 am

Right, before i go any further with this, i'm going to fit a new roll pin.

Although i can't move the shaft by hand, when under a load it may move about, so let's make sure.

What size is the roll pin??

Ta!
touring_19_16v
Level 10 User

Joined: 27 Apr 2005
Posts: 620

Posted: Mon Dec 19, 2005 3:13 am

tiny lil thing theres two in there a outer and inner 1 shouldnt be much from reno
Chris H
Forum Moderator

Joined: 02 Mar 2004
Posts: 19978

Posted: Mon Dec 19, 2005 3:44 am

30p from ren and theresa 2 kingds, the twin pin touring mentioned or the single pin.
touring_19_16v
Level 10 User

Joined: 27 Apr 2005
Posts: 620

Posted: Mon Dec 19, 2005 3:51 am

y did they design 2 pins that do the same job?
Dan
Site Subscriber

Joined: 28 Jan 2005
Posts: 3547

Posted: Mon Dec 19, 2005 4:16 am

I think it was more of a case of what was closest to the production line rather than designing.
Display posts from previous:      


 Jump to:   




SPIDER ARCHIVE
Powered by phpBB © 2001, 2002 phpBB Group :: FI Theme :: All times are GMT - 7 Hours